ESC Specifications
Application Guidelines: 1:5 scale vehicles with a maximum weight of up to 13.6 kg and the Castle 2028 motor included
Vehicle examples: Losi DB XL-E™, Losi Super Rock Rey™, Arrma Kraton 8s™, Arrma Outcast 8s™, Traxxas X-Maxx™. Note: Some vehicles may require aftermarket parts to allow installation of ESC and/or motor.
Input voltage range:
MIN: 3S LiPo, MAX: 8S LiPo 33.6V
Run Modes:
Sensored, Sensorless, Brushed and SmartSense™ in combination with a Castle...
mehr anzeigen
weniger anzeigen
ESC Specifications
Application Guidelines: 1:5 scale vehicles with a maximum weight of up to 13.6 kg and the Castle 2028 motor included
Vehicle examples: Losi DB XL-E™, Losi Super Rock Rey™, Arrma Kraton 8s™, Arrma Outcast 8s™, Traxxas X-Maxx™. Note: Some vehicles may require aftermarket parts to allow installation of ESC and/or motor.
Input voltage range:
MIN: 3S LiPo, MAX: 8S LiPo 33.6V
Run Modes:
Sensored, Sensorless, Brushed and SmartSense™ in combination with a Castle 4-pin 12-slot sensor motor.
Brake:
Proportional
Reversible:
Yes, but can be disabled for racing.
On / Off Switch:
Yes, waterproof
Fan:
Yes, factory equipped (50mm), fully removable** (see product usage notes)
Size:
Length: 3.98 inches (101.2 mm), Width: 2.49 inches (63.3 mm), Height: 2.2 inches (55.8 mm)
Weight (with cables):
13.1 oz (371 g)
Motor connections:
8-mm female bullets
Items needed for operation:
The Mamba XLX2 requires the use of connectors rated for 150+ amps of continuous power, such as Castle 6.5 mm polarized or CC BULLET 8.0 mm
Operating Environment:
Waterproof design for all weather conditions (see Operating Environment Considerations)
Programmability:
Fully programmable Castle function set with Castle Link USB adapter and free downloadable Castle Link Windows software or Castle Link app and a B-LINK Bluetooth adapter (sold separately).
Telemetry connectivity:
Yes, with Castle Creation's Telemetry Link for S.BUS2 and Futaba T4PX, T7PX and T7PXR transmitters.
Technical Tips:
The Mamba XLX2 has threaded mounting holes on the bottom of the controller. There are four M3 mounting holes with a maximum depth of 5mm; they are spaced 46mm apart in width and 40.2mm apart in length. Use this template to help align and position the screw holes.
Motor specifications
Input voltage range:
12 seconds maximum (8 seconds maximum with XLX2)
Kv: 1100
Max. RPM: 45,000
Motor size: Length: 4.4" (113.2mm)
Diameter: 2.2" (57mm)
Shaft Size:
Length: 30mm
Diameter: 8 mm
Weight (with cables): 44 oz. / 1.25 kg
Mounting hole specifications: 4 mm at 30 mm spacing
Fan: Available, but not included (011-0019-00)
Connectors: 8.0 mm male.
Items needed for operation: N/A
Product Usage Explanations:
Do not use mounting screws that extend more than 5 mm into the front of the motor. Using a screw that is too long may cause damage to the motor windings and is not covered under warranty.
Application Guidelines: N/A
Max. Recommended Vehicle Weight:
Vehicles weighing less than 13.6 kg
Technical Notes:
Running modes: sensorless and sensor controlled
Water resistant design:
The sensor board has a conformal silicone coating to protect the sensors from moisture. The sensor connections are not waterproof; water can cause loss of signal, which can lead to loss of sensor functions. Castle recommended applying dielectric grease to the outside of the sensor cable connections after cable installation. Routine maintenance is recommended after running in wet conditions. For information on operating and maintaining motors in wet environments, refer to the manual