Technical data Mamba Micro X2 ESC
Input voltage range:
2S-4S LiPo (max. 16.8 V) BEC specifications :
No internal BEC in ESC. External 10 amp CC BEC included. Operating environment :
Waterproof* design allows use in almost any environment; included CC BEC is not waterproof. Brake :
Proportional Reversible :
Yes, but can be disabled On / Off Switch :
Yes, waterproof Fan :
Coming soon, uses a 25mm fan...
mehr anzeigen
weniger anzeigen
Technical data Mamba Micro X2 ESC
Input voltage range:
2S-4S LiPo (max. 16.8 V)
BEC specifications :
No internal BEC in ESC. External 10 amp CC BEC included.
Operating environment:
Waterproof* design allows use in almost any environment; included CC BEC is not waterproof.
Brake:
Proportional
Reversible:
Yes, but can be disabled
On / Off Switch :
Yes, waterproof
Fan:
Coming soon, uses a 25mm fan
Size (L x W x H):
41.6 mm x 29.4 mm x 21.3 mm (1.64" x 1.16" x 0.84")
Weight (with wires):
1.66 ounces / 47 grams
Connectors:
4.0 mm bullets
Items needed for operation: battery connection required:
Castle 4.0 mm Polarized Connectors , Deans Ultra Plugs and XT60 are recommended.
Product Use Statements:
Applying voltages above 16.8 volts will cause irreparable damage to your controller and void your warranty.
The recommended battery capacity for 1:18 scale vehicles is 1500 mAh. We recommend using LiPo batteries with 30 °C continuous discharge or higher (or high quality 25 °C batteries like Traxxas® Power Cell).
Mamba Micro X has 4.0 mm round plugs on the motor cables and the battery input cables are bare. You will need to add the plug of your choice to the battery cables. We recommend a high current plug rated at least 40 amps.
Programmability
Additional settings and software updates are available via the Windows®-based Castle Link software and USB adapter, or the Castle Link app for Android or iOS and a B-LINK Bluetooth adapter (sold separately).
Telemetry Link Capable:
Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX transmitters.
Technical Notes:
*Although the Mamba Micro X2 is waterproof, it is not intended for operation while fully immersed in liquid. They may corrode if exposed to corrosive materials such as salt water. Always rinse the speed controller with clean water after exposing it to corrosive materials or dirt. Although the controller may be waterproof, we recommend users confirm that the rest of their vehicle, including the batteries, servos, radio, and chassis, are also waterproof before exposing them to liquids of any kind.
Technical Data 1010-4400 kV Sensor Motor
Input voltage range:
2S-4S LiPo
Kv:
4400
max. speed
80.000
Size: Length:
59.5 mm
Diameter:
28.25 mm
Weight (with wires) :
5.17 ounces (46.5 g)
Stock Size :
Length: 15 mm
Diameter: 1/8" (3.17 mm)
Mounting Hole Specifications:
M2.5 at 14 mm and 16 mm; M3 at 19 mm
Connectors: 4-mm Castle Bullet connectors attached to 16-gauge replaceable wire; includes 210-mm sensor cable.
Application Guidelines: Ideal for 1:14 and 1:16 vehicles weighing up to 3 lbs and up to 4s LiPo
Technical Notes:
Running Modes: SmartSense™ Sensored and an ultra-efficient Sensorless mode.
If you are running 4s and using two 2s LiPos in series, please refer to this BEC wiring diagram .
Waterproof design: the sensor board is coated with a conformal silicone coating to protect the sensors from moisture. The sensor connections are not waterproof; water can cause loss of signal which can result in loss of sensor capability. Castle recommends applying dielectric grease to the outside of the sensor cable connectors after cable installation. Routine maintenance is recommended after running in wet conditions. Please refer to this document for operation and maintenance of motors in wet environments.