ESC Technical data
Input voltage range: 2S-4S LiPo (max. 16.8 V) (max. 2s with included 1007-8450 kV motor)
BEC specifications: No internal BEC in ESC. External 10 amp CC BEC included.
Operating Environment: Waterproof* design allows use in almost any environment; included CC BEC is not waterproof.
Brake: Proportional
Reversible: Yes, but can be disabled
On / Off switch: Yes, waterproof
Fan: Coming soon, uses a 25mm fan
Size (L x W x H): 41.6 mm x 29.4 mm x 21.3 mm...
mehr anzeigen
weniger anzeigen
ESC Technical data
Input voltage range: 2S-4S LiPo (max. 16.8 V) (max. 2s with included 1007-8450 kV motor)
BEC specifications: No internal BEC in ESC. External 10 amp CC BEC included.
Operating Environment: Waterproof* design allows use in almost any environment; included CC BEC is not waterproof.
Brake: Proportional
Reversible: Yes, but can be disabled
On / Off switch: Yes, waterproof
Fan: Coming soon, uses a 25mm fan
Size (L x W x H): 41.6 mm x 29.4 mm x 21.3 mm (1.64" x 1.16" x 0.84")
Weight (with wires): 1.66 ounces / 47 grams
Connectors: 4.0 mm bullets
Items needed for operation: Battery Connector Required: Castle 4.0 mm Polarized Connectors , Deans Ultra Plugs and XT60 are recommended.
Product Use Statements:
Applying voltages above 16.8 volts will cause irreparable damage to your controller and void your warranty.
The recommended battery capacity for 1:18 scale vehicles is 1500 mAh. We recommend using LiPo batteries with 30 °C continuous discharge or higher (or high quality 25 °C batteries like Traxxas® Power Cell).
Mamba Micro X has 4.0 mm round plugs on the motor cables and the battery input cables are bare. You will need to add the plug of your choice to the battery cables. We recommend a high current plug rated at least 40 amps.
Application Guidelines: Ideal for 1:16 and 1:14 scale vehicles weighing up to 2.75 lbs.
max. recommended vehicle weight: 2.75 pounds
Programmability: Additional settings and software updates are available via the Windows®-based Castle Link software and USB adapter, or the Castle Link app for Android or iOS and a B-LINK Bluetooth adapter (sold separately).
Telemetry Link Capable: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX transmitters
Technical Notes:
If you are running on 4s and using two 2s LiPos in series, please refer to this BEC wiring diagram .
*Although the Mamba Micro X2 is waterproof, it is not intended for operation while fully submerged in liquid. They may corrode if exposed to corrosive materials such as salt water. Always rinse the speed controller with clean water after exposing it to corrosive materials or dirt. Although the controller may be waterproof, we recommend users confirm that the rest of their vehicle, including the batteries, servos, radio and chassis, are also waterproof before exposing them to liquids of any kind.
Motor Technical Data
Input voltage range: 2s LiPo
Kv: 8450
Max speed: 80.000
Can size: length: 50.3 mm
diameter: 28 mm
weight (with wires): 4.05 ounces (114.8 g)
Shaft size:length: 15 mm
Diameter: 1/8" (3.175 mm)
Mounting hole specifications: M.5 for 14 mm and 16 mm; M3 for 19 mm
Connectors: 4-mm Castle Bullet connectors attached to 16-gauge replaceable wire; includes 210-mm sensor cable
Items needed for operation:compatible Electronic Speed Controller (ESC)
Application Guidelines: Ideal for 1:16 and 1:14 scale vehicles weighing up to 2.75 lbs.
Recommended ESC(s): Mamba Micro X2
Running Modes: SmartSense™ (with Castle Sensor-enabled ESC), Sensored and an ultra-efficient Sensorless mode.
Technical Notes:
Waterproof Design: The sensor board is coated with a conformal silicone coating to protect the sensors from moisture. The sensor connectors are not waterproof; water can cause loss of signal, which can lead to loss of sensor capability. Castle recommended applying dielectric grease to the outside of the sensor cable connectors after installing the cable. Routine maintenance is recommended after running in wet conditions. Please refer to this document for operation and maintenance of motors in wet environments.